MIDI Kinetics Forum

Hi all

it s a beginner question but i don t know how to change linear fader behaviour to a logarithmic behaviour?

I use osc lemur line.

Thank in advance

G

Hi
Basic answer is you can't, there is no linear/log option as such . . .

But there are built-in functions for log() & log10() that give you natural (e) or common (10) logs . . .
Oh and also the pow() function . . .
These can be used in various ways in scripts, functions etc

Hope that helps, What exactly are you wanting to do?
MM

I'm also interested in this question. In my case it is a softsynth that has logarithmic faders. I tried with the functions you mentioned, but failed to make it work. I should try again, invest more time and brain. Shouldn't be that difficult.

Macciza wrote:Hi
Basic answer is you can't, there is no linear/log option as such . . .

But there are built-in functions for log() & log10() that give you natural (e) or common (10) logs . . .
Oh and also the pow() function . . .
These can be used in various ways in scripts, functions etc

Hope that helps, What exactly are you wanting to do?
MM

Thank you for the answer.

I need to use a log fader to control a duration knob, in a (Usine Hollyhock) granulation patch. In the granulation pach, this knob must be in a log mod. the scale is 2ms to 750 ms, and if i use linear fader to control this duration knob, it isn t sound good.

G

So

can you explain to me how to use this log () function?
i imagine that i have to write it in a script.

G

Hmm, I'm not a maths geek particularly . . .
It really depends on what exactly you want to do . . . (as always . . )
If you are using midi mapping type stuff to control things you are use values from 0-127 . . .
Things can interpret this differently to span various ranges in various ways . . .
Getting values to match up can be somewhat difficult in many cases . . .

Some specifics - first, Granulation can 'not sound good' quite easily depending on lots of variables....
Had a quick look a Usine H and the Granulator patch it also has a section that lets you alter its response
It looks like the Mapping pane lets you change how it responds to incoming midi from say a MultiBall in Lemur
This can give you a more linear response if that is what you are after - halfway across multiball is halfway through range
the other option would be to get Lemur to send its midi in a log/exp manner as needed . . .

Really need more info of what control or response you are after . . .
I'll see if I can do up some examples

Hi Macciza:

Macciza wrote:Hmm, I'm not a maths geek particularly . . .
It really depends on what exactly you want to do . . . (as always . . ):

It s certainly because my english is so bad.
Anyway i will try to be as clear as possible:

I need to use a log curve fader to control a grain duration knob, in a (Usine Hollyhock) granulation patch.
The scale is 2ms to 750 ms and i wish prefer a log curve to control this values.

"Some specifics - first, Granulation can 'not sound good' quite easily depending on lots of variables...."

I Know that,
Thank a lot if you can answer

G

I'm working on it I'll have a answer very soon

Not sure if this is right or not , it certainly appears to act like a log pot you can also scale its max and min values

nice one!

Although in my case, I need exactly the contrary. This logfader makes the softsynth's faders behave even worse. But it's a good start. I guess I need an exponential fader that starts slowly from 0 and ends quickly to 127. The math I haven't found yet, I admit that it's a bit too much right now.

And then I'd need the feedback from the softsynth, which will be another task. I think it's not worth the effort. It's not such an important softsynth for me. Rather some kind of challenge.

But I hope this logfader will be of good use for others.